Ground Control Logo 15 Years of Satellite Communications
Sales@GroundControl.com | U.S. - 800.773.7168 | International +1.805.783.4600
    Home  >  Products  >   SCADA / M2M Solutions  >  All BGAN Terminals    >  Hughes 9502 BGAN  >  Hughes 9502 Solar Solution
  Solar Sentry for the Hughes 9502
   
 

Install a pole-mounted Hughes 9502 in no-power locations. These solutions provide high-grade solar panels
from 20 watts to 375 watts, a pole mounted enclosure, a high amp-hour battery (or two) and charge controller.

Hughes 9502 Solar Solution

Solar Sentry Features
20 to 375 watt Solar Panel(s) - Oil-Gas safety rated
All weather, lockable enclosure
High amp-hour all weather sealed battery(s)
Charge controller for solar panel & batteries
Room to add additional equipment inside enclosure

BGAN 9502 Features
Operates Globally - Coverage Map
Temperature rated -40°F to 167°F (-40° to 75° C).
9502 uses 3-4 watts of power for full time network
9502 uses .01 watts for 30 second network wakeup
Provides speeds of up to 448 Kbps
Uses special BGAN M2M service designed for M2M
Powerful firewall protection, at no added cost
Stays Alive TCP-IP connection. Real-time monitoring

Worldwide Service Area
BGAN M2M Coverage Map
BGAN M2M service is available everywhere, except for the extreme polar regions. If an install location is within one of the three colored areas above, it can connect.
BGAN M2M Coverage Map


$1095 - 20 Watt System (shown above and below) - Unassembled - (minimum 10 quantity order required)
Includes all aluminum enclosure, 20 watt solar panel, 1 deep-cycle closed-cell battery, charge controller,
two pole mounting brackets for solar panel and the Hughes 9502 2-piece BGAN terminal (sold separately).

$1795 - 125 Watt System - Unassembled - (minimum 10 quantity order required)
Includes all aluminum enclosure, one 125 watt solar panel, 2 deep-cycle closed-cell batteries, charge controller,
two pole mounting brackets for solar panel and the Hughes 9502 2-piece BGAN terminal (sold separately).


Questions on the Solar Sentry? Please email sales@groundcontrol.com


Hughes 9502 Solar Sentry Photos    
Solar Sentry Prewired   Solar Sentry With Sensors
In this solution, the Hughes 9502 is secured inside the all aluminum enclosure, that includes a solar charge controller, a 54 amp hour battery that will keep the 9502 running for 5 days without sunlight for a full-time network connection. Additional batteries may be added.
Here the enclosure shows the installation of a sensor controller with 4 attached sensors, a DC battery voltage monitor, air temperature, air humidity, and a DC power relay to turn on and off a light under the enclosure. More information on Controller & Sensors.
Sensor Monitor Main Screen   Live View Of Solar Sentry
While any SCADA or M2M sensor package may be used, our solution uses the AKCP 4 sensor controller with several attached sensors. This web based interface lets you monitor, and set warning levels for many kinds of sensors. More information on the AKCP controller and sensors.
 
A Live Demonstration of the Solar Sentry Solution. The above screen is a screenshot from a live video feed used in the demonstration. Please call for more information.
Pole Mount With Concrete   Non-Pen Mount for BGAN
In this installation, a 2" inch (outside diameter) galvanized pole was used with a 40 lbs bag of Quick-Crete. Most any size pole can be used with the solar sentry.
 
Ground Control offers Non-Penetrating mounting options for systems that are not permanent, or need to be moved from time to time.
M2M Sensors   Solar Sentry Top Package
There are a wide variety of SCADA and M2M sensors that monitor everything from temperature, to fuel level. You can also control remote equipment with AC or DC switches that are activated manually, or triggered by any event, such as temperature from another sensor.
The 20 watt solar panel and the Hughes 9502 antenna use the same mounting brackets.
Hughes 9502 Antenna On Mounting Bracket   Solar Panel 20 Watt
The Hughes 9502 antenna connect with a single, low-impendence cable with TNC connectors. Pointing the antenna only requires a set of headphones.
 
In this installation, the 20 watt solar panel from BP is premium grade construction, and is rated to operate with Oil-and-Gas standards. Up to 390 watt solutions are available.
Solar Sentry Enclosure   Solar Sentry Lock
The all aluminum enclosure will withstand the elements.
  The lock on the side of the enclosure.
Enclosure Weather and Insect Protected   Light Under Enclosure
Looking from the inside of the enclosure door, all vents are screen protected from insects. Also note the neoprene gasket that lines the front of the door for a tight weather seal.
 
On this installation, a light has been installed under the enclosure and can be activated by sensor limits (such as low temperature warnings), or motion detection, or manually over the Internet.
Hughes 9502 One-Piece holding in hand   Hughes 9502 One-Piece Bottom View
The Hughes 9502 One-Piece Terminal is excellent for locations that may not require an enclosure for remote equipment. (The Hughes 9502 standard system requires an enclosure).
 
The One-Piece places the Hughes 9502 terminal inside of a milled aluminum case with two caps on both ends to access the terminal controls. Removing the caps requires only a screwdriver with the four screw-bolts. These caps lock in place using the bar/plate (shown on top).

Questions on the Solar Sentry? Please email sales@groundcontrol.com
BGAN M2M
BGAN Main Page
All BGAN Terminals
BGAN M2M Service
Hughes 9502 Terminal
BGAN M2M Coverage
BGAN M2M Firewall
VPN and Private Network
Pole-Mount M2M Solution
BGAN M2M SCAP
SCADA / M2M Page
Link
 BGAN M2M Service Plans (global usage)
BGAN Sim Card The Hughes 9502 uses special M2M BGAN Service
plans from Ground Control

Hughes 9502 BGAN M2M Terminal Hughes 9502 BGAN M2M
Ultra-Low power consumption
Extreme Operation - cold or hot
Easy no-laptop installation
Low cost equipment

 

Copyright © 2002-2017 Ground Control. All Right Reserved.